* added a "Local Variables\ section to all .h and .c files

[olsrd.git] / files / olsrd.conf.default.rfc

diff --git a/files/olsrd.conf.default.rfc b/files/olsrd.conf.default.rfc
index 7f97797..58f6c74 100644 (file)
--- a/files/olsrd.conf.default.rfc
+++ b/files/olsrd.conf.default.rfc
@@ -15,6 +15,10 @@ DebugLevel   1
 
 IpVersion      4
 
 
 IpVersion      4
 

+# FIBMetric ("flat", "correct", or "approx")
+
+FIBMetric "flat"
+

 # Clear the screen each time the internal state changes
 
 ClearScreen     yes
 # Clear the screen each time the internal state changes
 
 ClearScreen     yes


@@ -118,16 +122,19 @@ HystThrLow        0.30
 
 #LinkQualityLevel      0
 
 
 #LinkQualityLevel      0
 

-# Link quality window size
-# Defaults to 10
-
-#LinkQualityWinSize    10
+# Link quality aging factor
+# Defaults to 0.05, smaller values mean larger LQ window size
+# LinkQualityAging 0.1 

 
 # Polling rate in seconds(float). 
 # Default value 0.05 sec
 
 Pollrate       0.05
 
 
 # Polling rate in seconds(float). 
 # Default value 0.05 sec
 
 Pollrate       0.05
 

+# Interval to poll network interfaces for configuration 
+# changes. Defaults to 2.5 seconds
+
+NicChgsPollInt  3.0

 
 # TC redundancy
 # Specifies how much neighbor info should
 
 # TC redundancy
 # Specifies how much neighbor info should


@@ -200,6 +207,15 @@ Pollrate   0.05
 
 Interface "XXX" "YYY"
 {
 
 Interface "XXX" "YYY"
 {

+    # Olsrd can autodetect changes in NIC
+    # configurations(IP address changes etc.). 
+    # This is Enabled by default and the interval
+    # to poll for changes on is defined by 
+    # NicChgsPollInt.
+    # This polling can be disabled pr. NIC by setting
+    # AutoDetectChanges to no.
+
+    # AutoDetectChanges            yes

 
     # IPv4 broadcast address to use. The
     # one usefull example would be 255.255.255.255
 
     # IPv4 broadcast address to use. The
     # one usefull example would be 255.255.255.255


@@ -254,6 +270,7 @@ Interface "XXX" "YYY"
     # HNA validity time
     # HnaValidityTime  15.0
 
     # HNA validity time
     # HnaValidityTime  15.0
 

+

     # When multiple links exist between hosts
     # the weight of interface is used to determine
     # the link to use. Normally the weight is
     # When multiple links exist between hosts
     # the weight of interface is used to determine
     # the link to use. Normally the weight is


@@ -261,9 +278,29 @@ Interface "XXX" "YYY"
     # on the characteristics of the interface,
     # but here you can specify a fixed value.
     # Olsrd will choose links with the lowest value.
     # on the characteristics of the interface,
     # but here you can specify a fixed value.
     # Olsrd will choose links with the lowest value.

-
+    # Note:
+    # Interface weight is used only when LinkQualityLevel is set to 0.
+    # For any other value of LinkQualityLevel, the interface ETX
+    # value is used instead.

     # Weight 0
 
 
     # Weight 0
 
 

+    # If a certain route should be preferred 
+    # or ignored by the mesh, the Link Quality 
+    # value of a node can be multiplied with a factor 
+    # entered here. In the example the route 
+    # using 192.168.0.1 would rather be ignored.
+    # A multiplier of 0.5 will result in a small
+    # (bad) LinkQuality value and a high (bad)
+    # ETX value.
+    # Note:
+    # Link quality multiplier is used only when
+    # LinkQualityLevel is > 0.
+
+    # LinkQualityMult 192.168.0.1 0.5
+
+    # This multiplier applies to all other nodes 
+    # LinkQualityMult default 0.8
+

 }
 
 }